Machine Operation
Lone Star Revolver with a NUM Controller
Lone Star Revolver with a NUM Controller PypeServer for the Lone Star Revolver with a NUM Controller This document covers topics specific to PypeServer output for Lone Star Revolvers with chucks, running NUM controllers. Topics in this document: ...
Calibrating the Vernon 5 Axis Machine
Calibrating the Vernon 5 Axis Machine Calibrating The Vernon MPM Machine This document covers the basics of making sure that your Vernon MPM machine is properly tuned and can cut parts as desired. Contents 1 Check machine tuning with WinMPM 2 2 Set ...
PypeServer for the Vernon Mini
PypeServer for the Vernon Mini PypeServer for the Vernon Mini This is a user's manual for using PypeServer with the Vernon Mini. It covers configuring both PypeServer and the Vernon Mini so they work together. Contents 1 Training Materials 1 2 Vernon ...
Manual Head Pivot Height
Manual Head Pivot Height Manual Head Pivot Height This document is for machines with a torch pivot height that can vary from being at the top of the pipe In the Settings ?? Machine Settings tab, in the Torch settings, the setting Manual Head Pivot ...
Serial Communications Testing
Serial Communications Testing Serial Communications Testing This document explains the possible causes of communications failures between PypeServer and the Watts Machine include, and provides tests that can be done to determine the cause. Here are ...
Lone Star Magnum with NUM Controller
Lone Star Magnum with NUM Controller PypeServer for the Lone Star Magnum with a NUM Controller This document covers topics specific to PypeServer output for Lone Star machines running NUM controllers. Topics in this document: PypeServer settings for ...
Pypeserver with EdgeConnect Machines
Pypeserver with EdgeConnect Machines PypeServer with EdgeConnect machines Machine configuration When configuring your machine, some preparatory steps are required in order to get meaningful test results. Getting axial directions correct This is done ...
Vernon Mini Beveling Setup
Vernon Mini Beveling Setup This document is from Lincoln Electric MPCP Setup Walkthrough After loading the pipe, jog the torch near to where the cut will be go to the back side of the torch and align the bevel alignment gauge with the top of the ...
LoneStar Machines Running Mach3
LoneStar Machines Running Mach3 PypeServer for Lone Star Machines Using Mach3 Controllers Table of Contents 1 General overview of network layout 2 2 PypeServer Settings Overview 3 2.1 Basic Machine Settings 3 2.2 Machine Properties 8 2.3 Torch ...
Getting Started with HGG Machines
Getting Started with HGG Machines PypeServer for HGG Machines This document covers topics specific to HGG machine working well with PypeServer. Topics include: General network layout for using PypeServer with the machine HGG ProCAM settings and ...
NC Code for Vernon Machines
NC Code for Vernon Machines PypeServer for Vernon Machines This document covers topics specific to Vernon machine working well with PypeServer. Topics include: General network layout for using PypeServer with the machine Vernon MPM settings and ...
Machine Tuning -- Troubleshooting
Machine Tuning -- Troubleshooting Parts are not cutting to design measurements-Troubleshooting This short document advises you on how to troubleshoot and tune your machine so that it cuts true to the dimensions in PypeServer. PypeServer does not make ...
Jog an Offset Before Making a Cut
Jog an Offset Before Making a Cut Jog an Offset Before Making a Cut Pause and set and offset before a cut This feature is very useful on large pipe that is out of round, or is distorting out of round as it is being turned. By checking the Pause to ...
Load With Last Cut in the Chuck
Load With Last Cut in the Chuck Load with last cut in the chuck If you have a pipe with a pre-cut, straight end-cut (typically with a ground bevel), you can put that end in the chuck and use that as the last cut of your last part. This also works for ...
Torch end of cut leadout and tuning
Torch end of cut leadout and tuning End of Cut Tuning (reducing gouge) There are several reasons you may see a gouge at the end of a cut. The Cause Gouging typically occurs when: The torch returns to the a location already cut-typically the start ...
Make a single cut on the pipe
Make a single cut on the pipe Trim the end of a pipe/Cut a pipe in half This function allows you to easily send a single straight or miter cut to the machine to make one cut (not cutting a two ended part). This functionality only appears when you are ...